Skip to content

Technical resources

Air Filter Class Reference

Two standards that get confused because they measure different things. Here is what each one says, and where each class belongs. Reproduced for convenience — the standard itself governs.

EN 1822

EPA, HEPA and ULPA classes

Efficiency at the Most Penetrating Particle Size — the size the medium is worst at. Local efficiency is the minimum permitted at any single point on the filter face, which is what a leak scan looks for.

  • E10EPA

    Integral efficiency
    ≥ 85 %
    Local minimum
    —

    Final filtration in non-critical supply; pre-filtration to a HEPA stage.

  • E11EPA

    Integral efficiency
    ≥ 95 %
    Local minimum
    —

    Secondary filtration protecting terminal HEPA filters.

  • E12EPA

    Integral efficiency
    ≥ 99.5 %
    Local minimum
    —

    Higher-duty secondary filtration in cleanroom air handling.

  • H13HEPA

    Integral efficiency
    ≥ 99.95 %
    Local minimum
    ≥ 99.75 %

    Terminal filtration for Grade C and D areas, and many ISO 7 and 8 rooms.

  • H14HEPA

    Integral efficiency
    ≥ 99.995 %
    Local minimum
    ≥ 99.975 %

    Terminal filtration for EU GMP Grade A and B zones.

  • U15ULPA

    Integral efficiency
    ≥ 99.9995 %
    Local minimum
    ≥ 99.9975 %

    Semiconductor and nanotechnology environments at ISO 1 to 4.

  • U16ULPA

    Integral efficiency
    ≥ 99.99995 %
    Local minimum
    ≥ 99.99975 %

    The most critical fabrication zones.

  • U17ULPA

    Integral efficiency
    ≥ 99.999995 %
    Local minimum
    ≥ 99.9999 %

    Specialist applications beyond normal cleanroom practice.

A certificate proves the filter. It does not prove the installation — a certified filter in a poor seal still leaks, which is what the installed filter leak test on site exists to find.

ISO 16890

General ventilation filters

A different measure for a different job: how well a pre- or secondary filter removes the particulate fractions that would otherwise load the terminal filter behind it.

ISO Coarse

Arrestance against coarse dust

First-stage protection for HVAC equipment; not rated against fine particulate.

ISO ePM10

Efficiency against particles up to 10 µm

Pre-filtration where the outdoor air burden is largely coarse.

ISO ePM2.5

Efficiency against particles up to 2.5 µm

Intermediate filtration in cleanroom air handling units.

ISO ePM1

Efficiency against particles up to 1 µm

The stage that determines how long a terminal HEPA filter lasts.

Classes from EN 1822-1:2019. EN 1822-1 © CEN; ISO 16890 © ISO. Obtain the standards from iso.org or your national standards body.

Questions

About filter selection

Classification reference
What is the difference between H13 and H14?
H13 removes at least 99.95 % of particles at the Most Penetrating Particle Size; H14 at least 99.995 %. In practice H14 is specified as terminal filtration for EU GMP Grade A and B zones, and H13 for many Grade C and D areas — but the deciding factor is the classification the room must hold, not the filter class in isolation.
What does MPPS mean, and why rate filters at it?
The Most Penetrating Particle Size is the particle size a filter medium captures least effectively, typically around 0.1 to 0.2 µm. Filters perform better above and below it. Rating at MPPS gives the honest worst case rather than a flattering average, which is why EN 1822 uses it.
How do EN 1822 and ISO 16890 relate to each other?
They measure different things and do not convert between one another. EN 1822 rates high-efficiency filters at MPPS with individual scan testing. ISO 16890 rates general ventilation filters against particulate matter fractions — ePM1, ePM2.5, ePM10 — which is the useful measure for the pre- and secondary stages that protect an expensive terminal filter.
Does a certified filter guarantee a compliant room?
No. A certified filter installed in a poor seal still leaks. What proves the installation is an installed filter leak test — an aerosol scan of the filter face, frame and seal, in place — which is a separate test from the manufacturer's certificate that came with the filter.
Which pre-filter class should protect a terminal HEPA?
The stage that most affects terminal filter life is ePM1, because sub-micron particulate is what loads the HEPA medium. The right selection depends on the outdoor air burden at the site, the recirculation ratio and the change interval you are willing to run — it is an economic calculation as much as a technical one.