Skip to content

Technical resources

Cleanroom Classification Reference

Every ISO 14644-1 class, every particle size, and the GMP grade each one answers to. Reproduced for convenience — the standard itself governs.

ISO 14644-1

Airborne particle limits by class

Maximum permitted particles per cubic metre, equal to or larger than the stated size. A dash means the standard does not define a limit at that size for that class.

ISO 14644-1 airborne particulate cleanliness classes
Class≥ 0.1 µm≥ 0.2 µm≥ 0.3 µm≥ 0.5 µm≥ 1 µm≥ 5 µm
ISO 110—————
ISO 21002410———
ISO 31,00023710235——
ISO 410,0002,3701,02035283—
ISO 5100,00023,70010,2003,520832—
ISO 61,000,000237,000102,00035,2008,320293
ISO 7———352,00083,2002,930
ISO 8———3,520,000832,00029,300
ISO 9———35,200,0008,320,000293,000

A class is only meaningful with its occupancy state attached. The same room is a different class as-built, at rest and in operation, and a limit quoted without one cannot be verified.

Limits from ISO 14644-1:2015, Table 1. ISO 14644-1 © ISO. Obtain the standard from iso.org or your national standards body.

EU GMP

Grade to ISO class

The particle classification each grade maps to. A grade carries microbiological limits, airflow and gowning requirements as well — design against Annex 1, not against this table.

A

The critical zone: open product, aseptic connections, filling.

At rest
ISO 5
In operation
ISO 5
B

The background environment to a Grade A zone.

At rest
ISO 5
In operation
ISO 7
C

Preparation and less critical stages of sterile manufacture.

At rest
ISO 7
In operation
ISO 8
D

Support areas: component handling, material entry, technical zones.

At rest
ISO 8
In operation
Not predetermined

Air change rates

Where the calculation usually lands

Bands, not values. The correct rate for a room comes from its calculated load, contamination generation and required recovery time.

Grade A / ISO 5 unidirectional

Velocity-driven: 0.36 – 0.54 m/s at the working position

Sized on airflow velocity across the zone rather than on room air changes.

Grade B / ISO 5 – 7

40 – 60 ACPH

High turnover to hold classification with personnel present.

Grade C / ISO 7 – 8

20 – 40 ACPH

Typical for preparation and compounding areas.

Grade D / ISO 8

10 – 20 ACPH

Support and material handling areas.

Controlled, unclassified

6 – 12 ACPH

Technical corridors and warehousing.

Questions

About classification

Open the glossary
What is the particle limit for ISO 5?
ISO 5 permits a maximum of 3,520 particles of 0.5 µm and larger per cubic metre, 100,000 at 0.1 µm and 832 at 1 µm. It is the class an EU GMP Grade A zone is held to, both at rest and in operation.
Which ISO class does EU GMP Grade B correspond to?
Grade B is ISO 5 at rest and ISO 7 in operation. The change reflects what people do to a room: the same air handling that holds ISO 5 in an empty room holds ISO 7 once gowned operators are working in it.
Why does the classification change between at rest and in operation?
Because occupancy generates particles. A classification is only meaningful with its occupancy state attached — as-built, at rest, or operational — and a limit quoted without one cannot be verified or audited.
Is a particle count enough to define a GMP grade?
No. A grade also carries microbiological limits, airflow requirements, gowning and monitoring expectations. The mapping on this page relates the particle classification only; a facility should be designed against EU GMP Annex 1 itself.
How many air changes per hour does a cleanroom need?
It is calculated, not looked up: from the room's heat load, its contamination generation and the recovery time it has to meet. The bands on this page are where those calculations usually land, and are useful as a sanity check on a number rather than as a substitute for one.