Skip to content

Services and Solutions

Maintenance Services

A cleanroom is qualified on one day and has to behave the same way every day after it. We hold that validated state with criticality-based planned maintenance, condition monitoring and IIoT trending that finds component wear before it becomes a deviation, and periodic requalification and instrument calibration that keep the evidence current.

Services and Solutions

Introduction

For facilities under a maintenance agreement, technicians provide round-the-clock corrective and emergency response across Southeast Asia, with critical spares held against the contract and an asset register for every system we service. The facility does not have to be one we built.

Overview

Holding the validated state for the life of the facility

A cleanroom is qualified on one day and has to behave the same way every day after it. Maintenance is what keeps the gap between those two things from opening.

Qualification proves a facility met its criteria at a point in time. Filters load, seals age, belts and bearings wear, dampers drift, sensors lose calibration, and a room that recovered in twelve minutes at handover takes twenty-five minutes two years later. None of this announces itself. It appears as a failed environmental monitoring result, a batch investigation, or an observation during an inspection.

We plan maintenance around what each asset does to product quality rather than around its purchase price. A criticality assessment sorts systems by their impact on the validated state, and that ranking sets inspection frequency, spares holding, response time and the depth of the record kept. A terminal HEPA housing serving a Grade B room and a comfort-cooling unit in an office both get maintained; they do not get the same regime.

Condition data is used where it earns its place. Vibration trends on critical fans, filter differential pressure, valve response times, energy signatures and environmental trending all show wear developing before it becomes failure, and let intervention be scheduled into a planned shutdown rather than forced during production.

Every visit produces a record. Work orders, service reports, calibration certificates, filter change records and requalification results are filed so the maintenance history of any system can be produced on request. Between inspections that record is the evidence that the facility has stayed in the state it was qualified in.

Capabilities

Scope of work

Preventive and predictive maintenance, with 24/7 response under service agreement, that keeps critical systems compliant and running.

Preventive Maintenance & Remote Monitoring

Moving beyond reactive repairs, we deploy planned preventive maintenance and remote IIoT monitoring. This reduces the risk of unplanned downtime in sensitive environments, protecting pharmaceutical batches and semiconductor wafers.

Predictive & Condition-Based Maintenance

Using trending data and IIoT analytics, we predict component wear before it leads to failure. Condition-based scheduling reduces unnecessary downtime and extends the service life of your critical assets.

24/7 Corrective & Emergency Support Under Maintenance Agreement

For facilities under a maintenance agreement, our technicians provide round-the-clock corrective and emergency response across Southeast Asia. Contracted response times and on-call expertise help keep your critical MEP systems running.

Validation, Calibration & Compliance

We keep your facility audit-ready throughout its operational life with periodic requalification, instrument calibration, and GMP-compliance documentation. Every service is recorded and traceable, protecting your validated state between regulatory inspections.

Spare Parts & Asset Management

We maintain critical spare-parts inventories and complete asset registers for every system we service. Planned availability of genuine components keeps response times short and your facility continuously in its validated state.

Technical Support & Performance Optimization

We partner with your team for the long term — providing on-site and remote technical support, operator training, and continuous performance optimization. Trending analysis and energy tuning keep your systems performing exactly as designed, year after year.

Our approach

How the service is set up and run

The first two stages are done once. The rest run on a cycle for as long as the contract lasts.

  1. Asset register and criticality assessment

    Every system in scope is surveyed and registered with its make, model, serial number, location, duty, service history and the rooms it serves. Each asset is then assessed for its impact on product quality, on the validated state and on continuity of production, and that ranking drives everything that follows.

    Output

    • Asset register with tagging
    • Criticality assessment
    • Baseline condition report
  2. Maintenance strategy and planned schedule

    A written strategy sets the maintenance policy for each criticality band — planned preventive, condition-based or run-to-failure — with task lists, frequencies, spares holding, competence requirements and acceptance criteria. The annual planned maintenance calendar is agreed against your production plan so intrusive work lands in planned downtime.

    Output

    • Maintenance strategy document
    • Annual PPM schedule and task lists
    • Critical spares list and stock levels
  3. Planned preventive execution

    Scheduled work is executed against defined task lists by technicians briefed on the room classifications they are entering and the gowning and permit regime that applies. Filter changes, belt and bearing service, coil cleaning, damper and actuator checks, drain and tray inspection and control verification are recorded task by task, with findings raised as separate work where corrective action is needed.

    Output

    • Completed work orders
    • Service reports and findings register
    • Filter change and consumable records
  4. Condition monitoring and predictive analysis

    Where criticality justifies it, condition data is collected and trended — vibration and thermal signatures on rotating plant, filter differential pressure, energy consumption, and environmental parameters drawn from the monitoring system. Trends are reviewed against alert and action limits so the repair of a developing fault is scheduled rather than forced.

    Output

    • Condition monitoring reports
    • Trend analysis and alert notifications
    • Recommended intervention plan
  5. Periodic requalification and calibration

    Cleanroom performance is retested at the intervals your quality system requires: particle counting, installed filter leak testing, airflow velocity and volume, pressure differential, recovery and, where specified, airflow visualization and containment leak testing. Instruments are calibrated against traceable references, and every result is issued with the acceptance criterion beside it.

    Output

    • Requalification protocols and reports
    • Calibration certificates with traceability
    • Out-of-tolerance investigation records
  6. Review, optimization and reporting

    Performance is reviewed with you on an agreed cycle — completion against plan, response times, recurring failures, spares consumption and energy trend. The strategy is adjusted where the evidence supports it, and optimization opportunities are put forward with the expected saving and any qualification impact stated up front.

    Output

    • Periodic performance and KPI report
    • Updated maintenance strategy
    • Energy and optimization recommendations

Technical parameters

Scope, intervals and response

Typical parameters. Frequencies and response times are fixed in the service agreement against your criticality assessment and quality system.

Cleanroom performance testing — ISO 14644-2 and 14644-3

Airborne particle countClassification retest to ISO 14644-1 at the interval set by the monitoring plan
Installed filter leak testAerosol scan of terminal filters and seals to ISO 14644-3
Airflow velocity and volumeUnidirectional velocity and total volume verified against the design schedule
Pressure differentialCascade verified across every classified boundary
Recovery testClean-up time to classified condition, compared with the qualified baseline
Airflow visualizationSmoke study for critical zones where the Contamination Control Strategy requires it
Requalification intervalGrade A and B at most 6 months; Grade C and D at most 12 months, per EU GMP Annex 1

Planned preventive maintenance

Terminal and final filtersInspected each visit; replaced on differential pressure, integrity result or elapsed service life
Pre- and secondary filtersScheduled replacement, typically quarterly to semiannually, depending on local air quality
AHU mechanical serviceFan, bearing, drive, damper, actuator, coil, drain tray and casing seal inspection
Hygiene inspectionInternal cleanliness, drainage and microbiological risk points on hygienic units
Controls and instrumentationSensor verification, control loop check, alarm and interlock function test
Clean utilitiesSanitization support, loop sampling support and instrument verification

Calibration

Instrument scopeTemperature, relative humidity, differential pressure, flow, particle counters and monitoring sensors
TraceabilityCalibrated against references traceable to national standards, certificate issued per instrument
IntervalTypically 12 months, shortened where criticality or drift history requires it
Out-of-tolerance handlingDocumented investigation with impact assessment on product and on the validated state

Support and response

Corrective and emergency support24/7 on-call coverage across Southeast Asia, for facilities under a maintenance agreement
Response timesFixed per criticality band in the service agreement
Remote monitoringIIoT-enabled trending and alarm notification where the site permits connectivity
Spare partsCritical spares held to agreed stock levels with consumption reporting
DocumentationWork orders, service reports, certificates and requalification records issued and archived

Deliverables

What you receive under a maintenance agreement

  • Tagged asset register and criticality assessment
  • Written maintenance strategy and annual PPM calendar
  • Task lists with acceptance criteria for each asset class
  • Completed work orders and signed service reports
  • Filter change records and consumable usage log
  • Condition monitoring and trend analysis reports
  • Requalification protocols, results and comparison against the qualified baseline
  • Calibration certificates with traceability statements
  • Deviation, out-of-tolerance and corrective action records
  • Critical spares register with stock levels and consumption
  • Periodic KPI report — plan compliance, response performance, recurring failures, energy trend
  • Operator training records where training is included in scope

Compliance

Standards the service is measured against

ISO 14644-2Monitoring to provide evidence of cleanroom performance
The monitoring plan and requalification interval framework.
ISO 14644-3Test methods
Particle count, installed filter leak test, airflow, pressure differential and recovery test methods.
EU GMP Annex 1Manufacture of sterile medicinal products
Requalification intervals, environmental monitoring expectations and the Contamination Control Strategy.
EU GMP Annex 15Qualification and validation
Periodic review, requalification and change control after handover.
ISO 9001Quality management systems
Procedures, records and corrective action across the service.
ISO 45001Occupational health and safety management
Permit to work, isolation and safe systems of work on client sites.
ISO 55001Asset management
Criticality-based strategy, lifecycle planning and performance review.

Talk to our engineers

Tell us about your facility and we will route your inquiry to the right engineering lead.

Insights

Technical notes from this practice

View all insights (39)

Technical resources

Free references for this work

The references we reach for ourselves. No sign-up, and where a figure comes from a standard, we name it.

Questions

Maintenance Service — questions we are asked

Answered by the engineers who do the work.

Cleanroom HVAC and air handling, terminal filtration, dehumidification, clean utilities support, controls and instrumentation, and the electrical and ELV systems serving them. Scope is set against the asset register and criticality assessment, so the agreement covers what affects product quality and continuity rather than a fixed equipment list.

EU GMP Annex 1 sets a maximum interval of six months for Grade A and B areas and twelve months for Grade C and D; your own monitoring plan and risk assessment may set shorter intervals. Requalification is also triggered by significant change — plant replacement, layout modification, or a sustained shift in performance.

Yes. Systems designed or installed by other suppliers are a normal starting point for a maintenance agreement. We begin with an asset survey and baseline condition report, which usually also identifies documentation gaps — missing filter schedules, uncalibrated instruments, undocumented control changes — and we agree on a plan to close them.

Response times are fixed per criticality band in the service agreement, with 24/7 on-call coverage across Southeast Asia for facilities under a maintenance agreement. Where a system is critical to the validated state, response time and critical spares holding are agreed together — a fast response is of limited use if the part is six weeks away.

Condition data is collected on the assets where it justifies the effort, then trended against alert and action limits. Rising vibration on a supply fan, a filter differential climbing faster than its curve, or a slow drift in recovery time all indicate developing wear. The value is scheduling the intervention into planned downtime instead of losing production to it.

Planned work is executed within your change control system. Like-for-like replacement to the qualified specification is handled as routine maintenance; anything that changes performance, configuration or software is assessed for requalification impact and agreed with your quality unit before it is carried out.

Frequently. Loaded filters, fouled coils, drifting dampers and controls left in override all raise fan and cooling energy. Restoring plant to its design condition, retuning set points and control sequences, and applying demand-controlled ventilation in unoccupied periods reduce consumption measurably. Each measure is checked against the recovery-time and pressure-cascade requirements before it is applied.