Skip to content

Newsroom

News & Insights

Company news from Humiley Group INC and technical notes on cleanroom HVAC, GMP validation, semiconductor environments and energy-storage engineering.

  • 780 articles

Everything

From the Humiley newsroom

85 articles tagged #Annex1.

Zero growth and the HVAC record around a media fill

Annex 1 sets zero growth as the APS target, and any contaminated unit fails it. The environmental side of the investigation starts from viable monitoring, with HVAC and EMS trends as support, so review trends before the fill, confirm logging and clock sync, and agree which HVAC events count as interruptions.

InsightRead

Pass boxes: where the grade boundary leaks

A pass box sits across a grade boundary designed for at least 10 Pa. The interlock does not fix a worn door seal, a static box is made safe by the disinfectant contact time rather than by waiting, and a dynamic box needs its supply balanced against both rooms and its HEPA filter leak tested.

InsightRead

Grade A is judged in operation

Grade A must meet ISO 5, 3,520 particles of 0.5 µm or larger per cubic metre, both at rest and in operation. An FFU array is therefore judged with operators and machines in the zone: uniform unidirectional flow, leak-tested H14 filters and a smoke study run with the real interventions.

InsightRead

HVAC changes and the repeat media fill

EU GMP Annex 1 (2022) lists significant modification to the HVAC system among the reasons to repeat an aseptic process simulation. Changes to airflow pattern, pressure regime or filter housings in aseptic areas should reach QA with an engineering note before the work, and the requalification should be planned with the shutdown.

InsightRead

Environmental monitoring locations and their rationale

Classification spreads sampling points evenly by floor area; environmental monitoring should go where contamination would reach open product first. Place particle probes and settle plates from the smoke study, the intervention list and a documented risk assessment, keep them clear of the flow, cover the last-to-recover spots, and reference the evidence behind each point.

InsightRead

3,520 per m³ is about 100 counts a sample

In EU GMP Annex 1 (2022), 3,520 particles of 0.5 µm and larger per m³ is both the Grade A classification limit and the Table 5 monitoring maximum. In a 28.3 L sample that is about 100 counts, and one count reads as about 35 per m³, so site alert levels are clearer written as counts per sample.

InsightRead

Grade A microbial limits for EU and US filings

Annex 1 (2022) sets Grade A microbial limits as no growth and requires any growth to be investigated; FDA's 2004 aseptic guidance gives ISO 5 action levels of 1 CFU/m³ and 1 CFU per 4-hour settle plate. A plant filing in both markets can write one stricter rule and one investigation route.

InsightRead

The revised EU GMP Annex 1 has applied since 25 August 2023, with point 8.123 following in 2024. A site still planning its gap assessment is years behind. Most findings land in the CCS, for example a pressure alarm delay set at commissioning that nobody can justify.

InsightRead

Sink or bubble: when product and operator both need protecting

In a live-organism suite, GMP pushes air out of the clean room while biosafety pulls it into the room holding the organism. A sink airlock below both neighbours or a bubble above them carries the compromise, and both depend on the door interlock. Each step still needs a measurable differential.

InsightRead

Particles of 5 µm and larger settle in long runs, impact in tight bends and stick to non-conductive tubing, so a remote counter can under-read the size channel Annex 1 watches. Keep lines short, bends generous and tubing conductive, and qualify transport loss on the installed line.

InsightRead

Grade B at rest is held to 3,520 particles ≥0.5 µm and 29 ≥5 µm per m³. Annex 1 (2022) defines at rest for GMP grades as HVAC running, main equipment installed and standing by, and no personnel, reached after a clean-up period of under 20 minutes as guidance. The protocol should record that condition.

InsightRead