A low leaving dew point can come from a deeper coil with warmer water or a compact coil with colder water. The first costs fan pressure every running hour; the second costs chiller COP, about 3% per kelvin in an ideal cycle. The cheaper option depends on hours, tariff and how much of the plant shares the water.
When a desiccant rotor loses its reactivation heater it keeps turning and soon stops drying. Control reactivation from the dew point leaving the rotor, alarm rotor rotation separately from the drive motor, write the heater-trip response into the URS, and time the dew point rise with a deliberate trip at OQ.
EN 1886 classes AHU casing strength by deflection at test pressure: D1 up to 4 mm/m, D2 up to 10 mm/m. On a high-static GMP supply unit, a flexing panel works its gaskets loose and leakage rises. Ask which class was tested, on what model box, and whether your design pressure fits.
When a DX compressor cycles off and the fan keeps running, the water film left on the coil re-evaporates into the supply air, so net dehumidification falls short of the rating at part load. Cleanrooms cannot cycle their fans, so they need modulating or staged capacity, or chilled water.
Heating 18 °C, 60% RH air to 22 °C drops the reading to about 47% RH while the air keeps 7.7 g of water per kilogram. A room that meets RH only on reheat has no margin for one fault. Trend reheat output beside room RH: rising reheat means the coil is losing latent capacity.
Cartons and labels from an 80% RH warehouse release moisture in a 20% RH packing room. If board gives up 2% of its weight, a 500 kg delivery adds 10 kg of water. Stage packaging in a controlled area, unwrapped, for a time set by weighing sample cartons.
Air leaving a coil at 12 °C and 95% RH reads about 50% RH at 22 °C with the same 8.3 g/kg of water. A duct RH sensor after the coil works at the top of its scale. Control the coil on dew point or leaving-air temperature, and keep duct RH after reheat as a wet-filter alarm.
A 15–25 °C store in Viet Nam needs active cooling. Split units give cheap N+1 redundancy but a short air throw and little humidity control. A chilled-water AHU ducts air to the top of tall racking and can control dew point, with dearer redundancy. Humidity limits on the labels usually decide it.
A 100 cm² door gap at 15 Pa passes about 110 m³/h, but only doors on the suite boundary cost fresh air. Internal door leakage returns through the neighbouring room's grille. For twenty doors with four on the boundary, the leakage to make up is 440 m³/h rather than 2,200 m³/h of wet tropical air.
An AHU casing is described by five EN 1886 classes: strength D1–D3, leakage L1–L3, filter bypass up to F9, thermal transmittance T1–T5 and thermal bridging TB1–TB5. A witnessed FAT can test leakage on the real unit; transmittance and bridging come from a laboratory model box, so the model box report belongs with the offer.
A dry-room door opening onto the plant room swaps about 2 m³ of air at 20 g/kg, bringing in roughly 48 g of water. A −40 °C room supplied at −50 °C needs about 730 m³ of supply air to absorb it. Airlocks with their own dry supply, interlocked doors and counted door-open time follow from that sum.
Light office wear is about 0.5 clo, while full cleanroom gowning sits nearer 1.0 clo, and standing line work is about 1.6 met or more. Gowned operators are comfortable cooler than office staff, so set the room temperature in the URS with QA and EHS before the load calculation sizes the coil.