Design qualification checks the design against the URS, so a URS written by the designer to match the drawings gives DQ nothing to challenge. The designer can draft wording and add numbers, but the owner's process, QA and production people should own and sign every requirement, and no line should be written to fit a chosen solution.
ISO 14644-1 sets class limits at six particle sizes, and ISO 7 has limits at only three: 352,000 at ≥0.5 µm, 83,200 at ≥1 µm and 2,930 at ≥5 µm per m³. A URS that states the class without the size and occupancy state leaves both to the protocol writer.
After an over-budget cleanroom HVAC tender, three savings recur: an EN 1886 L2 casing instead of L1, fewer room pressure transmitters, and deleted door drop-seals. Each can reappear as an OQ failure in airflow, alarm testing or pressure differentials, so check every line against its URS requirement and test before accepting it.
SEMI F47 expects semiconductor tools to ride through sags to 50% for 200 ms, 70% for 0.5 s and 80% for 1 s. Fan drives, contactors and controls are often bought to no such curve, so the tool stays up while the cleanroom loses airflow. Specify the support systems to the same curve.
FDA's 2004 aseptic guidance asks for at least 10–15 Pa between rooms of different classification; Annex 1 gives at least 10 Pa as guidance. Setting each cascade step at 15 Pa meets both. Holding it is harder: seals wear and filters load, so trend the differentials instead of waiting for alarms.
In unidirectional airflow at 0.45 m/s, a 28.3 L/min particle counter needs an inlet about 37 mm across to sample isokinetically, and a 100 L/min counter about 69 mm. An undersized inlet draws air in too fast, large particles miss it by inertia, and the ≥5 µm count reads low.
Micro-environments hold ±2% RH at the tool and let the room run a looser band. A 2 m³ enclosure at 0.4 m/s over 1 m² replaces its air every 5 seconds. Steady leakage is the harder case: with the room at 45% ± 5% RH, size the enclosure for 50% RH at the highest room temperature.
A 72 m³ Grade C room can read exactly 1,800 m³/h, 25 air changes, while one of its four HEPA terminals delivers 60% of design. Write OQ airflow criteria for each terminal as well as the room total, and rebalance a starved terminal before the recovery test.
EU GMP Annex 15 (2015) lists seven elements a validation master plan should cover. The summary of facilities and systems with their qualification status is the one inspectors use: last qualification, next requalification and open deviations, in one table rather than a paragraph of intent.
A fan wall keeps a GMP supply unit running when one fan fails, provided each fan has a backdraft damper so air cannot flow back through the stopped one. Each EC fan's rectifier adds harmonics, THDi around 35–42% with a DC choke. A single plug fan is simpler but needs a standby.
MHRA (March 2018), FDA Q&A (December 2018), PIC/S PI 041-1 (July 2021) and WHO TRS 1033 Annex 4 (2021) all rest on ALCOA+. The difference that matters in a response is who wrote each one and for whom, so cite first the text the inspector works from.
Tropical GMP HVAC cools to dehumidify and then reheats, all year. A heat recovery chiller sends condenser heat to the reheat coils: 1,000 kW of cooling at COP 5 rejects about 1,200 kW. Condensing at 50 °C instead of 37 °C cuts ideal COP by about 30%, so it suits steady reheat.