Skip to content

Newsroom

News & Insights

Company news from Humiley Group INC and technical notes on cleanroom HVAC, GMP validation, semiconductor environments and energy-storage engineering.

  • 780 articles

Life Sciences

Life Sciences

379 articles filed under Life Sciences.

Registration batch: what the term means for the plant

A registration batch, also called an exhibit or primary batch, is made to generate the data filed for registration. ICH Q1A(R2), the stability guideline, asks for data on at least three primary batches made by a process that simulates production. Their data underpins the shelf life, so make them on qualified equipment.

InsightRead

What plant steam brings into the supply air

A humidifier fed from the plant boiler injects the boiler's volatile treatment chemicals into the supply air. WHO's HVAC guideline for non-sterile products says chemicals that could have a detrimental effect on the product should not be added to the boiler system. Use a clean steam generator or a steam-to-steam humidifier, or assess every chemical, and state the steam quality in the URS.

InsightRead

Cleaning validation: five steps, and sampling is the fourth

Sampling is the fourth step of a cleaning validation. Before any swab, EU GMP Annex 15 (2015 text) expects a justified worst-case product, a carryover limit based on a toxicological evaluation, and sampling locations with recovery shown for each surface and method. Hold times belong to the run, and manual cleaning should be confirmed at a justified frequency.

InsightRead

Why two teams give the same failure mode 40 and 160

A risk priority number is three judgements on ranked scales, multiplied, so two competent teams can score one failure mode 40 and 160. ICH Q9(R1) says subjectivity cannot be completely eliminated but may be controlled. In practice: define the scoring scales, record the assumptions behind each score and use relevant data where it exists.

InsightRead

ASTM E2500: who verifies, and whose documents count

Two ideas in ASTM E2500 shorten qualification. Subject matter experts plan, execute and review verification, and in ISPE's summary of the 2025 edition the quality unit approves the plans and the final acceptance. Vendor documentation may be used as evidence if the vendor has been assessed. EU GMP Annex 15 (2015 text) allows some FAT tests to stand at IQ/OQ where justified.

InsightRead

What a room pressure reading cannot tell you about containment

A potent-compound suite at −15 Pa shows which way air crosses the room boundary. It does not show what the operator breathes when a liner is cut or a drum is tipped. That takes air sampling in the breathing zone, and the equipment's containment performance is verified with a surrogate powder test.

InsightRead

A new pack size on a line that is already qualified

Adding a pack size to a qualified packaging line is a change. Open a change control with a regulatory assessment, check format parts and settings against the qualified range, validate where the range moved, release artwork, codes and master data, then update the packaging instructions, the line clearance checklist and operator training.

InsightRead

When an instrument fails its as-found check, adjusting it straight away leaves two things unasked: how long it was wrong and what relied on it. Record the as-found values, find the last calibration that passed, list what depended on the readings since, have QA assess the impact, then adjust and review the calibration interval.

InsightRead

Cpk 1.33: a convention, and what the GMP texts say instead

A Cpk of 1.33 puts the nearer specification limit 4 standard deviations from the process mean. It is a statistical convention: EU GMP Annex 15 (2015 text) and the FDA guidance of 2011 recommend statistical tools and name no index. With 10 batches the confidence interval is wide, so report the batch count and the interval.

InsightRead

The 2013 text of EU GMP Chapter 1 lists the qualification status of relevant equipment and utilities among the items a product quality review should include. Engineering can make that line believable with four more inputs: changes in the period, excursions and trends, calibration and maintenance failures with product impact, and the status of engineering CAPAs.

InsightRead