Skip to content

Newsroom

News & Insights

Company news from Humiley Group INC and technical notes on cleanroom HVAC, GMP validation, semiconductor environments and energy-storage engineering.

  • 780 articles

Everything

From the Humiley newsroom

Announcements and company updates, alongside the technical notes our engineers publish from each practice.

True copy: when a scan can stand in for the original

A true copy is a copy of an original record that has been verified, by a dated signature or a validated process, to hold the same information, including context, content and structure. The MHRA guidance of 2018 says it may be retained in place of the original if a documented system is in place to verify and record the integrity of the copy.

InsightRead

One site, one name: a master statement for regulatory documents

The manufacturing license, the GMP certificate and the dossier often spell the same site three ways, and an assessor cannot know they are one place. Keep a one-page master statement of the legal name, official address and building identifiers, copy every regulatory document from it, and change it only under change control.

InsightRead

Pre-commission cleaning of chilled-water pipework

New chilled-water pipework carries mill scale, weld slag and swarf that settle in control valve seats and coil tubes. Bypass coils, valves and chillers, flush the mains, circulate the cleaning chemical, rinse to the agreed limits and dose inhibitor before the coils are opened. Then keep the water circulating until handover.

InsightRead

Why a hot plant room halves the life of a drive

Capacitor makers publish a rule of thumb: each 10 K rise in operating temperature roughly halves the life of an electrolytic capacitor. A drive in a 45 °C plant room will not last like the same drive at 35 °C. Record the temperature inside the panel on every maintenance round, and ventilate or cool panels that stay hot.

InsightRead

Two versions of one leaflet on the same shelf

When leaflet text changes and the item code stays, old and new stock look identical in the store. EU GMP Chapter 5 says obsolete printed packaging material should be destroyed and the disposal recorded. Give every printed component a version code, quarantine superseded stock on the effective date and check the code at line start.

InsightRead

Batch history is not a process validation

Tabulating twenty or thirty past batches was once called retrospective validation. The 2015 text of EU GMP Annex 15 (section 5) says it is no longer an acceptable approach: a traditional process should undergo prospective validation, with concurrent validation only in exceptional circumstances. The batch history belongs in ongoing process verification.

InsightRead

A desk check for the airflow diagram

An airflow diagram shows every room's supply, return and exhaust on one sheet. For each room, supply minus return minus exhaust must leave a leakage that matches the pressure cascade, and the room flows must add up at each AHU. Five checks at the desk find errors that otherwise appear during balancing.

InsightRead

P-F interval: what decides how often to inspect

The P-F interval is the time between the point where a failure first becomes detectable and the point of functional failure. An inspection has to come round more often than that, with time left to act. The interval depends on the failure mode and on the detection method, so one calendar frequency cannot suit every fault.

InsightRead

ICH Q12: three tools for changes after approval

ICH Q12 (2019) lists eight tools and enablers for post-approval changes. Three come first for a plant: established conditions, whose change necessitates a submission; a change management protocol approved in advance; and the PLCM document that lists them. Q12 says an effective quality system is necessary, and that use depends on the regulatory framework in place.

InsightRead

Receiving HEPA filters: what to check before fitting

A HEPA filter leaves the factory tested, then travels by container, forklift and scaffold. Check the cartons on arrival, match label class, serial number and rated airflow to the schedule and test report, store dry within the stacking mark, open only at a clean work area and inspect media and gasket under strong light before fitting.

InsightRead

What a variation is, and why engineering should ask early

A variation is a change to the terms of a marketing authorisation. In the EU system, Type IA changes are made and then notified, Type IB changes are notified before implementation, and Type II changes need approval first. The class follows the change rather than its cost, so ask regulatory affairs before the purchase order.

InsightRead

Self-check a drawing before it goes for review

A lead engineer's review time should go to engineering questions. Before sending a drawing, check the title block and revision against the register, name the design basis documents, match every tag and unit to the schedules, attach the calculation for each sized item, and do your own red-line pass on a printed copy.

InsightRead