Skip to content

Newsroom

News & Insights

Company news from Humiley Group INC and technical notes on cleanroom HVAC, GMP validation, semiconductor environments and energy-storage engineering.

  • 780 articles

Everything

From the Humiley newsroom

Announcements and company updates, alongside the technical notes our engineers publish from each practice.

Closing an NCR takes more than 'rectified'

An NCR marked 'rectified' has recorded a repair. To close it properly, state the requirement that was broken, contain the item, decide the disposition and name who decided, find the cause and check for the same fault elsewhere, then verify against the original requirement and attach the evidence.

InsightRead

When a signal cable screen is earthed at both ends

A room pressure signal that wanders when a drive ramps often has a cable screen bonded at both ends, carrying earth current beside a 4–20 mA signal. For analogue signals, bond the screen at one end, keep it continuous and insulated through junction boxes, and follow the instrument maker where the instruction differs.

InsightRead

The accelerated stability condition: 6 months at 40 °C / 75% RH

The ICH stability guideline sets the accelerated study at 40 °C ± 2 °C and 75% RH ± 5% RH for a minimum of 6 months. If long-term studies run at 25 °C/60% RH, a significant change there should be followed by intermediate testing. For the chamber, excursions beyond the tolerances for more than 24 hours should be described in the study report.

InsightRead

Five site checks before a panel is energised

A panel that passed its factory test has since been transported, lifted and cabled. Before the incomer is closed: inspect inside and check torque marks, measure and record insulation resistance, compare protection settings with the coordination study, prove earth continuity and phase rotation, and confirm tools are out and covers on.

InsightRead

Where the 30-day deviation deadline comes from

The 2013 text of EU GMP Chapter 1 and 21 CFR 211.192 speak of recording and investigating deviations, and neither gives a number of days. The 30-day limit is the site's own, and inspectors hold a site to its procedure. The alternative is also a site rule: a limit per risk class, with extensions only on a written reason and an interim risk assessment.

InsightRead

A supplier's standard IQ/OQ protocol was written for the standard machine, before your URS existed. EU GMP Annex 15 (2015) says site personnel should confirm its suitability before approval, and that vendor protocols may be supplemented. Trace each URS line to a test, then write a short supplementary protocol for the lines left uncovered.

InsightRead

Open ductwork on site and short-lived terminal HEPAs

Construction dust left in supply ducts ends up in the terminal HEPA filters, which then load in months. Order ductwork factory-cleaned and capped, store it off the floor, re-cap every open end at the end of each shift, inspect and wipe each section before connection, and fit the terminal filters last.

InsightRead

What an f2 of 50 says about two dissolution profiles

The similarity factor f2 compares two dissolution profiles on a scale where 100 is identical and a 10% difference at every time point gives 49.9. FDA and EMA guidance read 50 to 100 as similar, under conditions on units, time points and variability. It is one input to a comparison after a site change.

InsightRead

Replacing an EMS: migrate the data before the old system goes

When an environmental monitoring system is replaced, years of records move with it or become unreadable. List the records and retention periods, specify what moves, verify a trial migration, migrate under change control and keep the old data readable. The 2011 text of Annex 11 says validation should include checks on value and meaning.

InsightRead

How to read an ISO 8573-1 compressed air class

An ISO 8573-1:2010 class such as [1:2:1] is three limits in a fixed order: particles, water as pressure dew point, and total oil. Class 2 water is −40 °C or lower; class 1 oil is 0.01 mg/m³ or less. The class does not name a location, so state the point of use.

InsightRead